Yellow wires will cause damage to any aftermarket stereo. Label it or splice to constant wire on aftermarket stereo first.
You’ll then be rewarded with a 4-digit retrieval code, which will allow you to unlock your radio. Once you’re connected, you’ll be asked to provide your vehicle’s radio identification number, along with a special dealer access code. IMPORTANT - There are two (2) yellow*, two (2) gray and two (2)īrown wires in this harness. Dial 1-80 to connect with GM’s toll-free radio hotline. Installing Aftermarket Speakers and Proper Hook-up We hope this section of our site is helpful. This section of our website is to help you locate power wires when installing external add-ons and extras. Purchase the aftermarket wire harness! This makes the installation easier, does away with improper speaker phasing and can save a headache. Remove the audio amplifier from the vehicle.Chevrolet Car Audio - Wire Diagrams - Wire Color CodesĬar Stereo Repair | Car Stereo Removal | FAQ | Shipping for Repair | Contact Us i put the stock radio back in hooked up both plugs worked fine, unhooked the small plug no sound. Remove the audio amplifier screws (1).ġ7. thank you i just bought a 2002 tahoe and trying to put my 7' monitor in and i had it all hooked up and now sound. Remove the console assembly from the vehicle.ġ6. The radio is a snap to install in your Chevy Silverado, Tahoe, Surburban, Avalanche, or car. Disconnect the floor console electrical connector.ġ5. Installing a skirted flatbed on a chassis truckEMAIL US: SALESRONDOTRAILER.COMIN SYCAMORE, IL 60178 BY DEKALB ILLINOIS.We sell a wide v. Remove both front console side panel screws (1).ġ4. Its just something you need to watch for. That isnt a flaw in the panel or the radio. If the radio is set to far back, the face plate binds and doesnt open. Move both front seats to the fully rearward.ġ3. The radio I installed has a face plate that moves to give you access to the DVD drive. Take note of whats around the drilling area and work carefully to avoid damaging your truck. The NV2200 in-dash delivers high-performance entertainment, navigation and observation in one, with a 6.2' touch panel display. If you install the larger speakers, be safe when youre drilling the new mounting holes.
How to install a dvd deck in a 2002 2500hd Bluetooth#
6.2' Touchscreen Display Double DIN Multimedia DVD Receiver with Bluetooth by Furrion. Remove both rear console side panel screwsġ2. Furrion 6.2' Touchscreen Display Double DIN Multimedia DVD Receiver with Bluetooth (381576) 2.
Reposition the inboard seat track trim (1) in order to gain access to the rear console side panel screw (2).ġ1. Move both front seats to the fully forward.ġ0. Remove the 4 screws retaining the upper console bracket to the lower console bracket.ĩ. Disconnect the audio amplifier electrical connectors.Ĩ. Metra - Radio Installation Dash Kit for Most 2005 and Later Chrysler, Dodge, Jeep and Mitsubishi Vehicles - Black. So it sounds like a lot of us have had to or need to change a pulley.I know it should be pretty straight forward but is there anywhere someone simply has. Remove the bolts (1) retaining the console to the instrument panel (I/P).ħ. But it will defiantly NOT fit in place of the tape deck. I will test that out within the next few days. It MAY be a replacement for the little storage area below it with the door, as the current one has a CD rack in it. If equipped with a Bose(TM) amplifier, remove the radio amp fuse located under the hood electrical center.Ĥ. First off it does NOT replace the tape deck. Should be inside the center console, just pull the cup holders up to see if it is there.ġ. Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp.
0 kommentar(er)
